Customer Training
Register here for training with Ingersoll Rand to learn about our rotary and centrifugal product lines. Training includes both theory and hands on practical exercises.

The equipment used in these courses has been evaluated as Hazard Risk Category 2 (HRC-2). In accordance with NFPA 70E standards, HRC-2 rated equipment requires the following PPE for personnel working inside the arc flash boundary: Fire Retardant clothing (rated HRC-2 or 8 cal), rubber gloves + leather gloves, safety glasses, and hard hat with arc face shield.
Attendees must be wearing appropriate protective clothing as specified. For those traveling by air, we can provide a limited number of hard hats with arc face shields if required, rubber/leather gloves and safety glasses. If driving, please bring your own PPE.
Any student who fails to comply will not be allowed in the lab areas for any hands-on training portion of this class.
C302 Customer Basic Rotary Class
2019 Dates: April 16-18
Cost: $2350 per person
Description: This course is designed for operation or maintenance personnel and focuses on rotary compressors 50hp (37kW) and above, and their control systems. Upon completion of this course, you will understand the principles of air compressor systems, the components and accessories included in the rotary compressor system, maintenance and diagnostic procedures, and operation of the control panel. 40% of this course is hands-on.
Agenda:
- Day 1: Introduction to compressed air systems, identification of compressor, overview of rotary compressor components, overview of air & oil flow circuit, rotary compressor operation
- Day 2: Operation of the SE/SG & S3 Intellisys controller
- Day 3: Maintenance and diagnostics, compressed air system accessories
C313 Customer Sierra Oil-Free Rotary Class
2019 Dates: April 23-25
Duration: 3 days
Cost: $2350 per person
Description:This program is designed to prepare maintenance and service providers to properly maintain and service their Ingersoll Rand “Oil-Free” air compressors (Sierra and Nirvana). You will gain theoretical and practical knowledge of the design and operation of the equipment through classroom studies and hands-on activities.
Agenda:
- Day 1: Compressor overview and principles of operation, identification of compressor mechanical and electrical components, overview of electrical system
- Day 2: Operation of the SE/SG & S3 Intellisys controller
- Day 3: Airend and motor servicing, service, maintenance and diagnostics, troubleshooting

The equipment used in these courses has been evaluated as Hazard Risk Category 1 (HRC-1). In accordance with NFPA 70E standards, HRC-1 rated equipment requires the following PPE for personnel working inside the arc flash boundary: Fire Retardant clothing (rated HRC-1 or 4 cal), rubber gloves, safety glasses, and hard hat.
Attendees must be wearing appropriate protective clothing as specified. For those traveling by air, we can provide a limited number of hard hats with arc face shields if required, rubber/leather gloves and safety glasses. If driving, please bring your own PPE.
Any student who fails to comply will not be allowed in the lab areas for any hands-on training portion of this class.
C400 Basic Centrifugal Class
2019 Dates: August 27-29
Duration: 3 days
Cost: $2350 per person
Description: This course is designed to provide maintenance, engineering and operations personnel with an overview of the Centac centrifugal compressor.
Agenda:
- Day 1: Principles of operation, airflow, hydraulic flow, identification of mechanical and electrical components, control panel with amperage software
- Day 2: Routine service and maintenance, basic troubleshooting techniques
- Day 3: Disassembly, assembly and calibration of rotor assemblies (type 1-2-3 & 6)

The equipment used in this course has been evaluated as Hazard Risk Category 2 (HRC-2). In accordance with NFPA 70E standards, HRC-2 rated equipment requires the following PPE for personnel working inside the arc flash boundary: Fire Retardant clothing (rated HRC-2 or 8 cal), rubber gloves + leather gloves, safety glasses, and hard hat with arc face shield.
Attendees must be wearing appropriate protective clothing as specified. For those traveling by air, we can provide a limited number of hard hats with arc face shields if required, rubber/leather gloves and safety glasses. If driving, please bring your own PPE.
Any student who fails to comply will not be allowed in the lab areas for any hands-on training portion of this class.
C451 Customer Centac MicroController (CMC)
2017 Dates: April. 10-14
Duration: 5 days
Cost:
- Days 1 - 3 ⇒ $1,900/person
Recommended for customers who have the standard CMC software. - Days 1 - 4 ⇒ $2,600/person
Recommmended for customers who have the advanced CMC software. - Day 5 ⇒ + $700/person
Recommended for customers who have the CMC Service Tools software. (Day 5 Only is also an option.) Note: Attendees for Day 5 - Customer must have purchased a licensed copy of the CMC Service Tool software.
Description: This course is designed to introduce technicians and engineers to Centac Controls and the CMC Service Tools software while teaching operation, maintenance, tuning, and troubleshooting basics.
Agenda:
- Day 1: CMC control basics; Centac principles of operation, Centac performance curve, CMC control methodologies
- Day 2: CMC hardware, user Interface data and settings for limit amp control
- Day 3: PID control loops and tuning
- Day 4: Ambient control; parallel valve logic, additional advanced features
- Day 5: CMC Service Tools Software; installation, software structure, downloading/changing programs, tuning and troubleshooting tools, and additional features only accessible through the Service Tools software
Requirements: Participants are responsibe for bringing laptop computers for the CMC Service Tools Software training. A minimum of one computer for every two people is required.
